TRIM & FLASHING GUIDE ROOFING Ridging -pg.1 Valley -pg.2 Barge Trim -pg.3 Drip Edge -pg.5 Soffit -pg.7 Fascia -pg.8 Side Wall -pg.9 End Wall -pg.10 Transition Flashing -pg.11 Gambrel Flashing -pg. 12 WALLS Window/Door -pg.13 Outside Flashing -pg.14 Inside Flashing -pg.15 Wall Trim/Flashing -pg. 16 Base Trim/Flashing -pg.16 FOAM CLOSURES GUIDE -pg.17

Trims and Flashings shown in this brochure are standard but can be modified to customer specifications upon request and by pre-order. Don’t see what you’re looking for? Give us a call to discuss custom trims. We are able to make trims to meet most custom requirements. Mile 1, Iguana Creek Road, Spanish Lookout | Call/WhatsApp text message: 823-0118 | email: [email protected] | website: www.koopsheet.com

1

RIDGING & HIP Ridging is a roofing trim that covers the gap at the peak of a roof where two opposing roof slopes join. This can be both along a horizontal peak (ridge installed straight across) of the roof as well as a covering for a hip (a ridge installed at a downward slope). Valley

• • •

16” wide x 8’ long (in stock) 24” wide x 8’ long (in stock) custom length available by pre-order

3”

metal color shows on this side

Transition Flashing Side Wall Flashing

Hip

Fascia Drip Edge

FOAM CLOSURES: Foam Closures seals the openings between roofing panels that stops dust, birds, insects, and wind driven rain from getting into your roof/building at the ridging, hip, valley and eaves. Available solid or vented. SEE PAGE 17

Need a Ridge Flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order. Below is an example of a “Ridge flashing”.

31/2”

31/2”

5/8”

metal color shows 31/2” on this side 5/8”

31/2”

3/8”

3/8”

RIDGING (Flashing profile)

PLAIN (SQUARED) FOAM CLOSURE SCREWS ROOFING PANEL

IDGIN

G

OUTSIDE FOAM CLOSURE

HIP R

Roof

End Wall Flashing

Barge Trim

7/8”

7/8”

Ridge

RIDGING ( KSM STANDARD PROFILE )

RELATED ACCESSORIES (STRAIGHT RIDGE) • Tacky Tape (helps eliminate leaks) • Outside Foam Closures • Color Matching Screws

RELATED ACCESSORIES (HIP RIDGE) • Tacky Tape (helps eliminate leaks) • Universal foam closure • Color Matching Screws

2

VALLEY Valleys protect the intersection where two roof planes meet, directing rainwater runoff away from the roof.

24” wide x 8’ long (in stock) custom length available by pre-order

Transition Flashing

7/8”

Valley

• •

7/8”

Ridge

VALLEY ( KSM STANDARD PROFILE )

Side Wall Flashing

87/8” Barge Trim

End Wall Flashing

metal color shows on this side

87/8”

3” Hip

Fascia Drip Edge

Need a Valley Flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order. Below is an example of a “W-Shape Valley Flashing”.

FOAM CLOSURES: Foam Closures seals the openings between roofing panels that stops dust, birds, insects, and wind driven rain from getting into your roof/building at the ridging, hip, valley and eaves. Available solid or vented. SEE PAGE 17

1/2” H

EM

1/2”

metal color shows on this side

W-VALLEY: A raised ridge running the length of the valley • Prevents water from running across the valley and onto the other side of the roof • Gives additional strength and rigidity to the flashing

101/

HEM

2”

101/

2”

HEM: A hemmed edge is one that has been folded over for added safety • Reduces the possibility of injury (such as cuts or slices to fingers) • Adds strength to outer edges of flashing • Helps eliminate leaks

SCREWS PE HA

”S

“W LEY

L VA 6”

Roof

ING

SH FLA N.

MI

PLAIN (SQUARED) FOAM CLOSURE

RELATED ACCESSORIES • Tacky Tape (helps eliminate leaks) • Foam Closure • Screws

3

BARGE TRIM (FOR ROOFS WITH OVERHANG) Barge Trim is a roofing trim attached to the gable (sloped) edge of a roof covering the exposed edges of the roofing panels. It protects the roof from moisture seeping underneath the edges & beneath the roofing panels.

10’ length in stock sold at any length up to 10’ long by pre-order

1”

4”

1/2”

Side Wall Flashing

1/2”

End Wall Flashing

Hip

> Using this profile, the barge trim is fastened to the major rib of the panel

Fascia

as illustrated in Figure 1.0

Drip Edge

METAL FASCIA CAP: Metal fascia goes over the fascia frame that is installed along the roofing edge of your home. Fascia & Soffit closes the gap between the walls and the roof of a structure.

FIGURE 1.0 ROOFING PANEL BARGE TRIM

SOFFIT: Soffit is a panel designed to cover the exposed area right under the gable & eaves overhang. It protects the inner roofing structure from pests, moisture or heat damage & improves the overall look of your roof/home.

SCREWS @ EVERY 24”

IM

TR

IT

FF

J-C

HA

NN

EL

TACKY TAPE

TS

AME

Need a Barge Trim/Flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order. Below is an example of a “Barge Trim/Flashing”.

?”

FIGURE 1.1

metal color shows on this side

?” ?”

1/2”

> Using this profile, the barge trim is fastened to the flat of the panel as illustrated in Figure 1.1 > Dimensions will vary with type of roofing panel

AP FASCIA C

SOFFI

R FASCIA F

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Tacky Tape (helps eliminate leaks) • Fascia Cap • Soffit Panels

3/4”

metal color shows on this side 3”

SO

Roof Edges

Barge Trim

• •

Transition Flashing

Valley

Ridge

BARGE TRIM ( KSM STANDARD PROFILE )

4

BARGE TRIM (FOR ROOFS WITH NO OVERHANG) Use the following barge trim profile for roofs with no overhang. The barge trim covers & protects the exposed edges where the roof meets the wall.

ROOFING PANEL BARGE TRIM SCREWS @ EVERY 24” TACKY TAPE

SCREWS @ EVERY MAJOR RIB SIDING PANEL

OUTSIDE FOAM CLOSURE

Roof Edges

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Tacky Tape on Roof (helps eliminate leaks) • Use Outside Foam Closure to match siding profile (for vertically installed corrugated or R panel siding)

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Tacky Tape on Roof & Siding (for horizontally installed corrugated or R panel siding)

5

DRIP EDGE (FOR ROOFS WITH OVERHANG) Drip Edge is a roofing trim attached to eaves (drip edge) of a roof, covering the exposed edges of the roofing panels. It protects the roof from moisture seeping underneath the edges & beneath the roofing panel.

DRIP EDGE ( KSM STANDARD PROFILE ) • •

10’ length in stock sold at any length up to 10’ long by pre-order

2” Valley

Ridge

metal color shows on this side

Transition Flashing Side Wall Flashing

3” 1/2”

Roof Edges

Barge Trim

End Wall Flashing

Hip

> This profile fits a 4:12 pitch. > The outward angled lip on a drip edge flashing redirects water away

Fascia Drip Edge

from the fascia and into the gutters, preventing water leakage between the fascia.

INSIDE FOAM CLOSURE SCREWS ROOFING PANEL DRIP EDGE

SOFFITS

SOLID OR VENTILATED SOFFITS AVAILABLE

J-CHANNEL

SOFFIT TRIM

SIDING PANEL

RELATED ACCESSORIES • Inside Foam Closures (to match your roofing profile) • Sealant (to seal flashing joints) • Color Matching Screws • Fascia Cap • Soffits Without a drip edge, water could get behind the gutter, causing leaks & potentially damaging the structure of your roof, especially wooden facia boards where the gutters are attached. If the fascia board begins to rot, you’ll begin to experience issues with gutter performance. INSTALLATION TIP: To prevent a dripping gutter, the drip edge is installed under the roofing sheet and should completely cover the top edge of the fascia & over the gutter. It should extend beyond the fascia and a minimum 1/3 of the gutter width as shown in the illustration below:

Need a Drip Edge Trim/Flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order.

6

DRIP EDGE (FOR ROOFS WITH NO OVERHANG) Drip Edge should be installed on roofs with no overhangs. The drip ege caps off the wall panels & protects the siding from moisture or water damage. Without a drip edge, water could get behind the siding panel & potentially damage the structure of your wall.

RELATED ACCESSORIES • Inside Foam Closures (to match your roofing profile) • Use Outside Foam Closure to match siding profile (for vertically installed corrugated or R panel siding) • Use Tacky Tape on Siding (for horizontally installed corrugated or R panel siding) • Sealant (to seal flashing joints) • Color Matching Screws

INSIDE FOAM CLOSURE ROOFING PANEL DRIP EDGE OUTSIDE FOAM CLOSURE

Roof Edges

SIDING PANEL

7

SOFFIT SOFFIT

NO SOFFIT

Soffit is a panel designed to cover the exposed area right under the gable & eaves overhang. It protects the inner roofing structure from pests, moisture or heat damage & improves the overall look of your roof/home. Soffits can be ventilated or solid (non-vented).

Roof Edges

VENTILATED SOFFITS: Ventilated soffits features small holes that allow air to travel in and out of the roof area; it allows heat or moisture to escape & fresh air to enter. Fresh airflow throughout the roof space ensures that your roof remains dry and free from moisture damage on sheeting and roof structure.

NON VENTILATE SOFFITS: Solid Soffits no holes and is a solid panel used to completely seal the eaves of your roof however, if you still require require air circulation, there are other products that you can install to create air flow through the roof area: Soffit vents

Gable Vents

Wind Turbines

Ridge Ventilation

Solid Soffit is available in: • White Aluminum (12" coverage x 12' long - in stock) Solid Soffit is available in: • White Aluminum (12" coverage x 12' long - in stock) • KSM custom soffit (KSM designed to cover 14") -width and design can be customized to your requirements -sold at any length up to 10' long by pre-order

DOES MY ROOF NEED SOFFIT? It protects your roof from structural damage... __________ -without soffits, your attic and rafters are vulnerable to rain being blown in. Water causes moisture damage - mildew, mold and rot are likely to occur and is the cause of roof rot and poor air quality.

It protects your roof from bats, birds, insects and other pests... __________ -without soffits, it is easy for these pests to make their homes under your roof or attic space damaging your roof and things like your electrical systems. These pest can also contribute to unhealthy air quality.

It improves insulation to some extent... __________ -without soffits, your energy bills can increase, since heat and cold air can easily travel through the exposed underside of the roof, meaning you have to either heat or cool your home more.

It provides support for your gutter system & adds curb appeal to your home. __________ Our aluminum and metal soffits are very durable and water-resistant & can also be used for interior paneling. Other budget friendly soffit panels e.g Wooden or PVC are easily damaged over a short period of time by heat & moisture.

8

FASCIA Fascia is a metal flashing that covers the exposed vertical (upward) edges of your roof at the gable & eaves overhang. Like soffits, a fascia protects the inner roofing structure from pests, moisture or heat damage & improves the overall look of your roof/home.

STANDARD PROFILE •

sold at any length up to 10’ long by pre-order in any KSM color and in of these standard sizes or in any size you require.

metal color shows 1” on this side 1” x 6” x 1” 1” x 8” x 1” 1” x 9” x 1” 1” x 10” x 1”

10”

Roof Edges

1”

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Color Matching Screws • Soffit Panels

METAL FASCIA CAP SOFFITS

SOLID OR VENTILATED SOFFITS AVAILABLE

DOES MY ROOF NEED METAL FASCIA? Metal fascia is very durable & resistant to heat & water damage... __________

Metal fascia boards is resistant to termites & pests... __________

It provides support for your gutter system... __________

-using metal fascia or covering your existing wooden fascia boards will extend its life span by protecting it from these rippling effects:

-using metal fascia or covering your existing wooden fascia boards will extend its life span by protecting it from woodlice, termites and other pest.

-fascia boards secure the gutters to the roof and keep them in place. A worn-out fascia boards can no longer hold the gutter fasteners in place, causing the gutter system to come loose and eventually detach from your roof.

• • •

water stains your wooden fascia boards wooden fascia boards rot & crack due to constant sun exposure a damaged wooden fascia board can retain moisture, which leads to the spread of mold and mildew

Metal fascia boards add curb appeal to your home... __________ -using metal fascia or covering your existing wooden fascia boards keeps your home protected for a very long time while adding to your home’s curb appeal. Forget about the hassle of painting wooden fascia boards our fascia products are available in White or you can choose from a variety of high quality color coated metals that will retain its good looks year after year even in the most

9

SIDE WALL FLASHING (SIDE MOUNT) The Side Wall flashing is designed to be used at the sides on a wall that transitions to a roof, dormer or chimney. Sealants & outside closures are necessary for a proper seal.

•

sold at any length up to 10’ long by pre-order

metal color shows on this side

4”

Valley

Ridge

STANDARD PROFILE

Transition Flashing Side Wall Flashing

5 1/4”

1”

Wall To Roof

1/2” Barge Trim

End Wall Flashing

Hip

> Use this profile if flashing can be covered with siding as

illustrated below. It is preferable to have the top leg of the side wall flashing go underneath the siding at least 4” above the roof deck.

Fascia Drip Edge

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Tacky Tape (helps eliminate leaks) • Inside Foam Closure (to match roof profile) • Outside Foam Closure (to match roof profile) • Color Matching Screws

SIDING PANEL SCREWS INSIDE FOAM CLOSURE SIDE WALL FLASHING SCREWS @ EVERY 24” TACKY TAPE ROOFING PANEL

Need a Side Wall Flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order. Below is an example of a “Side Wall Flashing”.

concrete wall

1/2” 4”

metal color shows on this side 5 1/4”

sealant

1” 3/4” 1/2”

> Use this profile if you are flashing a metal roof onto a concrete wall. Use an angle grinder to cut a 1/2” deep slot into the wall. Blow out dust & fill with sealant. Insert the upper 1/2” lip of the end wall flashing. The sealant will secure this joint & create a watertight seal.

tacky tape

roofing panel

Installation tips: When overlapped, flashing should be attached immediately adjacent to a major rib and not in between two major ribs.

10

END WALL FLASHING (TOP MOUNT) End Wall Flashing is designed to be used at the front on a wall that transitions to a roof, dormer or chimney Sealants & foam closures are necessary for a proper seal.

STANDARD PROFILE

sold at any length up to 10’ long by pre-order

4”

Ridge

Valley

Transition Flashing

metal color shows on this side

Side Wall Flashing

61/2”

Barge Trim

End Wall Flashing

1” 1/2”

> Use the profile below if flashing can be covered with siding as Hip

illustrated below. Roof slope should be mentioned if roof exceeds 5/12 pitch.

Fascia Drip Edge

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Inside Foam Closure (to match your roof profile) • Outside Foam Closure (to match your roof profile) • Color Matching Screws

SIDING PANEL

INSIDE FOAM CLOSURE SCREWS

END WALL FLASHING

OUTSIDE FOAM CLOSURE Need an End Wall Flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order. Below is an example of an “End Wall Flashing”.

concrete wall

1/2” 4”

metal color shows on this side 1” 6” 1/2”

sealant

> Use this profile if you are flashing a metal roof onto a concrete wall.

Use an angle grinder to cut a 1/2” deep slot into the wall. Blow out dust & fill with sealant. Insert the upper 1/2” lip of the end wall flashing. The sealant will secure this joint & create a watertight seal.

On existing vynl or wood siding, insert the upper 1/2” lip of the end wall flashing underneath the notch of the siding and secure this joint with sealant to create a watertight seal.

ROOFING PANEL

Wall to Roof

•

11

TRANSITION FLASHING The transition flashing prevents leakage by providing a continous drainage at the point where two different roof slopes meet. It is sealed on the lower side with outside closures, and can be sealed underneath the upper panels with inside closures.

•

sold at any length up to 10’ long by pre-order

1/2”

Transition Flashing

Valley

Ridge

STANDARD PROFILE

7 1/

Side Wall Flashing

2”

metal color shows on this side 6 1/2”

Roof

Barge Trim

End Wall Flashing

Hip

1” 1/2”

>Roof pitch or degree of angle is required when ordering flashing

Fascia Drip Edge

INSIDE FOAM CLOSURE

SCREWS TRANSITION FLASHING ROOFING PANEL OUTSIDE FOAM CLOSURE RELATED ACCESSORIES • Sealant (to seal flashing joints) • Inside Foam Closure (to match your roofing profile) • Outside Foam Closure (to match your roofing profile) • Color Matching Screws

Need a Transition Flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order.

12

GAMBREL FLASHING The gambrel flashing is used to seal the hip joint on a gambrel style roof.

STANDARD PROFILE •

sold at any length up to 10’ long by pre-order

6 1/2”

metal color shows on this side

2”

7 1/ 1/2”

>Roof pitch or degree of angle is required when ordering flashing

ROOFING PANEL

SCREWS

SCREWS

GAMBREL FLASHING INSIDE FOAM CLOSURE OUTSIDE FOAM CLOSURE

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Inside Foam Closure (to match your roofing profile) • Outside Foam Closure (to match your roofing profile) • Color Matching Screws

Need a Gambrel Flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order.

ROOFING PANEL

Roof

ROOF FRAME

13

WALL TRIM Wall trim helps ensure that moisture doesn’t seep in where panels join together or to flash the joint where two different siding applications meet.

R-PANEL SIDING SCREWS

STANDARD PROFILE

WALL TRIM 3” metal color shows on this side

92 -95 degree angle used for drainage)

2”

Wall

3”

INSIDE FOAM CLOSURE OUTSIDE FOAM CLOSURE

1/2” WALL FRAME RELATED ACCESSORIES • Sealant (to seal flashing joints) • Inside Foam Closure (to match your roofing profile) • Color Matching Screws

R-PANEL SIDING

Need a flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order.

W

BASE TRIM Base drip seals off the bottoms of panels at the floor level, where it helps to prevent the entrance of rodents and insects. It also provides a base for the setting of siding panels.

STANDARD PROFILE

metal color shows on this side

92 -95 degree angle used for drainage

3”

BASE TRIM

R-PANEL SIDING

WALL FRAME

1”

2” 1/2”

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Inside Foam Closure (to match your roofing profile) • Color Matching Screws

INSIDE FOAM CLOSURE CONCRETE BASE

14

WINDOW/DOOR FLASHING SIDING PANEL

2X4 WOODEN WINDOW (TOP) FRAME

The following are standard dimensions for trimming windows/doors on metal siding.

INSIDE FOAM CLOSURES

STEP 1. WINDOW TOP FLASHING WINDOW UNIT 1 1/2”

1 1/2”

3” This flashing keeps the water from coming into the house.

STEP 2. WINDOW TOP TRIM

1 1/2”

1/2”

1/2”

WINDOW UNIT

STEP 3. WINDOW SIDE & BOTTOM TRIM 2 1/2”

2X4 WOODEN WINDOW (BOTTOM) FRAME

1 1/2” 1 1/2”

SIDING PANEL

1/2”

Window & Door

1 1/2”

Need window & door trims/flashing custom made to your requirements? Custom flashings can be made up to 10’ in length by pre-order.

15

OUTSIDE FLASHING Used for waterproofing where two walls form an outside corner. Outside Flashing is sold in any KSM color to match your metal siding color.

STANDARD PROFILE • • •

10’ length in stock in most KSM colors & different sizes: 4” x 4” custom length available by pre-order 6” x 6” edges can be plain or hemmed 8” x 8”

1/2” HEM

Wall Corners

10” x 10” 12” x 12”

metal color shows on this side

Outside Flashing can also be used as an attractive detail trim for outside corners on Vynl & Wooden Siding or Cement Walls.

OUTSIDE FLASHING ON HORIZONALLY INSTALLED R-PANEL SIDING

1/2” HEM

HEM: A hemmed edge is one that has been folded over for added safety • Reduces the possibility of injury (such as cuts or slices to fingers) • Adds strength to outer edges of flashing

OUTSIDE FLASHING ON VERTICALLY INSTALLED R-PANEL SIDING

R-PANEL OUTSIDE FOAM CLOSURE

OUTSIDE FLASHING

OUTSIDE FLASHING

R-PANEL SIDING R-PANEL SIDING

TACKY TAPE SCREW

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Outside Foam Closure (to match siding profile) • Color Matching Screws

RELATED ACCESSORIES • Sealant (to seal flashing joints) • Tacky Tape (helps eliminate leaks) • Color Matching Screws • Use Plain Foam Closure if flashing edge will extend beyond a major rib

16

INSIDE FLASHING Used for waterproofing where two walls form an inside corner. Inside Flashing is sold in any KSM color to match the color of your metal siding. Recommended accessories are listed below for a total seal.

STANDARD PROFILE • • •

10’ length in stock in most KSM colors & different sizes: 4” x 4” custom length available by pre-order 6” x 6” edges can be plain or hemmed 8” x 8”

1/2” HEM

10” x 10” 12” x 12”

1/2” HEM

Inside Flashing can also be used as an attractive detail trim for inside corners on Vynl or Wooden Siding or Cement Walls.

HEM: A hemmed edge is one that has been folded over for added safety • Reduces the possibility of injury (such as cuts or slices to fingers) • Adds strength to outer edges of flashing

INSIDE FLASHING ON VERTICALLY INSTALLED R-PANEL SIDING

Wall Corners

metal color shows on this side

TACKY TAPE SCREW INSIDE FLASHING SCREW

RELATED ACCESSORIES • Use Tacky Tape on Siding (for vertically installed corrugated or R panel siding) • Use Outside Foam Closures in place of tacky tape if corrugated or R panel siding will be installed horizontall (straight across) • Sealant (to seal flashing joints)

R-PANEL SIDING

Valley

17

Ridge

Transition Flashing

FOAM CLOSURES

Side Wall Flashing

In order for a metal roof to be completely weatherproofed, you must use foam closures to fill the gaps left between the roofing sheets and the structure of the roof. These strips of foam prevent dust, wind-driven rain, birds, insects and other animals from getting into your roof/building at the ridging, hip, valley and eaves. Foam closures are designed to easily fit to any profile and are available solid or vented.

PLACE

Barge Trim

End Wall Flashing Hip

Drip Edge

TYPES OF FOAM CLOSURE (SOLID) provides a solid, water -tight & air-tight barrier

RIDGING

EAVES

Fascia

Outside Foam Closure (Available for R panel, Corrugated & Metal Tile Roofing) •Use on a horizontally installed ridge (straight line across) •O.F.C matches the width of the roofing panel hence one closure fits one sheet •O.F.C is designed with interlocking ends to provide a continous seal (except for the corrugated foam) **** IMPORTANT: The 30” long - Corrugated Foam Closure matches the profile of the 32” wide corrugated sheet. Contact a sales rep to help calculate the amount of foams you would require when using the 43” Wide Corrugated Sheet.

VENTILATED FOAM CLOSURE

a water-retardant, insect resistant barrier which improves roof ventilation.

Flex-O-Vent Foam (ROLL) This foam closure allows hot air to escape from the roof & allows fresh air to infiltrate the building. This is necessary for moisture control; fresh flowing air helps control the humidity that builds in your attic, which can cause mold.

Inside Foam Closure (Available for R panel, Corrugated & Metal Tile Roofing) •I.F.C fills the gaps at the eaves ends of sheets •I.F.C matches the width of the roofing panel hence one closure fits one sheet •I.F.C is designed with interlocking ends to provide a continous seal (except for the corrugated foam) **** IMPORTANT: The 30” long - Corrugated Foam Closure matches the profile of the 32” wide corrugated sheet. Contact a sales rep to help calculate the amount of foams you would require when using the 43” Wide Corrugated Sheet. FLAT (1 slope) Foams fill the gap on both ends of the sheets

HIPS

GABLE (2-Sided) ROOF Foams run along the eaves ends of sheets

HIP (4-sided) ROOF Foams run along the entire perimeter of the roof

Available for R panel & Corrugated Metal Roofing

• 2” thick X 3” wide X 20’ long (roll)

OPTION 2: Emseal Foam (Roll of 19.68ft)

IMPORTANT: For Tile Roofing application, ONLY the 2” Flex-O-Vent fills the gap

a self expanding sealant that fills a gap - often used to ensure a good seal. ****

Available for Metal Tile Roofing ONLY

45 Degree- Left & Right Hand (33” Coverage)

matches the profile of the Tile roofing panel at a 45 degree angle

**** Foams will run along both sides of the slope.

• 1.5” thick X 3” wide X 10’ long (roll)

OPTION 1: 36” Plain Foam Closure Strip (Square Profile)

a universal (squared) foam closure that conforms to the shape of the gap

VALLEYS

Available in these sizes and length